Unable to boot under latest firmware `5.13.1`.

[GamePlayer-8]

Hello,

I've installed your linux image & headers and after reboot I'm unable to start VisionFive2 (no pings, no screen output neither green led blinking).

I've used it with firmware from VisionFive2 5.13.1 firmware release.

Any way to boot up your kernel on that?

[inindev]

If you are trying to run a recent upstream kernel on a older vendor supplied downstream version of Linux, I would not expect this to work.

[Mecrisp]

I am running into the same issue here. I came from the https://github.com/starfive-tech/VisionFive2/releases/tag/JH7110_VF2_515_v5.13.1 release of the firmware flashed using

flashcp -v u-boot-spl.bin.normal.out /dev/mtd0
flashcp -v visionfive2_fw_payload.img /dev/mtd2

which successfully boots into the vendor SD card image, and then got the stock Debian image from https://github.com/inindev/visionfive2/releases/tag/v13-6.11 and put this on a SD card, which does not boot, no video, no green blinking, as described.

I understand I need a different combination of firmware files installed for this. But the instructions on the main page mentions flashing a different set of firmware images to the SPI flash only for changing the boot order. I am a bit confused... Could you please add a note what firmware files need to be flashed in order to boot the stock Debian image from SD card? Can I still boot other SD cards after flashing your patched one? I am a bit hestitant to just trying all combinations, as I will probably loose the ability to flash firmware images if I mess this up, effectively bricking the board.

[Mecrisp]

After I found the guide for recovery at https://doc-en.rvspace.org/VisionFive2/Quick_Start_Guide/VisionFive2_SDK_QSG/recovering_bootloader%20-%20vf2.html went on with more confidence, and followed the bootloader flashing instructions with u-boot-spl.bin.normal.out and u-boot.itb taken from https://github.com/inindev/visionfive2/releases/tag/v13-6.11

With this flashed, and visionfive2_trixie-v13-6.11.img on SD-Card, trying to boot results in this error message on the serial port:

dwmci_s: Response Timeout.
dwmci_d: DATA ERROR!
BOOT fail,Error is 0xffffffff

Switching the SD card back to the vendor image still boots properly.

Next I tried the SD card image from https://github.com/inindev/visionfive2/releases/tag/v13-6.6.5 in combination with the already flashed v13-6.11 firmware. This one boots, as seen on the serial console, but does not show any graphics output. I connected a 1920x1080 monitor.

Full console log:

dwmci_s: Response Timeout.

U-Boot SPL 2023.10-01055-gb98965c1fd (Dec 09 2023 - 14:58:20 -0500)
DDR version: dc2e84f0.
Trying to boot from MMC2


U-Boot 2023.10-01055-gb98965c1fd (Dec 09 2023 - 14:58:20 -0500)

CPU:   rv64imafdc_zba_zbb
Model: StarFive VisionFive 2 v1.3B
DRAM:  8 GiB
Core:  130 devices, 24 uclasses, devicetree: board
MMC:   mmc@16010000: 0, mmc@16020000: 1
Loading Environment from SPIFlash... SF: Detected gd25lq128 with page size 256 Bytes, erase size 4 KiB, total 16 MiB
*** Warning - bad CRC, using default environment

Loading Environment from nowhere... OK
StarFive EEPROM format v2

--------EEPROM INFO--------
Vendor : StarFive Technology Co., Ltd.
Product full SN: VF7110A1-2250-D008E000-00000601
data version: 0x2
PCB revision: 0xa1
BOM revision: A
Ethernet MAC0 address: 6c:cf:39:00:21:fd
Ethernet MAC1 address: 6c:cf:39:00:21:fe
--------EEPROM INFO--------

starfive_7110_pcie pcie@2b000000: Starfive PCIe bus probed.
starfive_7110_pcie pcie@2c000000: Starfive PCIe bus probed.
In:    serial@10000000
Out:   serial@10000000
Err:   serial@10000000
Net:   eth0: ethernet@16030000, eth1: ethernet@16040000
starting USB...
Bus xhci_pci: Register 5000420 NbrPorts 5
Starting the controller
USB XHCI 1.00
scanning bus xhci_pci for devices... 6 USB Device(s) found
       scanning usb for storage devices... 0 Storage Device(s) found
Working FDT set to ff7319d0
Hit any key to stop autoboot:  0 
switch to partitions #0, OK
mmc1 is current device
Scanning mmc 1:3...
Found /boot/extlinux/extlinux.conf
Retrieving file: /boot/extlinux/extlinux.conf
1:      Debian GNU/Linux trixie/sid 6.6.5-3051-riscv64
Retrieving file: /boot/vmlinuz-6.6.5-3051-riscv64
Retrieving file: /boot/initrd.img-6.6.5-3051-riscv64
append: root=UUID=2574fd6e-2dbd-4304-a269-a1fe902ce21d rootwait
Retrieving file: /boot/jh7110-starfive-visionfive-2-v1.3b.dtb-6.6.5-3051-riscv64
## Flattened Device Tree blob at 46000000
   Booting using the fdt blob at 0x46000000
Working FDT set to 46000000
   Loading Ramdisk to fe1bd000, end fe724349 ... OK
   Loading Device Tree to 00000000fe1b1000, end 00000000fe1bc45b ... OK
Working FDT set to fe1b1000

Starting kernel ...

[    0.000000] Linux version 6.6.5-3051-riscv64 (linux-kernel@github.com/inindev) (gcc-13 (Debian 13.2.0-8) 13.2.0, GNU ld (GNU Binutils for Debian) 2.41.50.20231206) #3051 SMP Debian 6.6.5-3051 (2023-12-08)
[    0.000000] Machine model: StarFive VisionFive 2 v1.3B
[    0.000000] SBI specification v2.0 detected
[    0.000000] SBI implementation ID=0x1 Version=0x10003
[    0.000000] SBI TIME extension detected
[    0.000000] SBI IPI extension detected
[    0.000000] SBI RFENCE extension detected
[    0.000000] efi: UEFI not found.
[    0.000000] OF: reserved mem: 0x0000000040000000..0x000000004003ffff (256 KiB) nomap non-reusable mmode_resv1@40000000
[    0.000000] OF: reserved mem: 0x0000000040040000..0x000000004005ffff (128 KiB) nomap non-reusable mmode_resv0@40040000
[    0.000000] cma: Reserved 16 MiB at 0x00000000ff000000 on node -1
[    0.000000] Zone ranges:
[    0.000000]   DMA32    [mem 0x0000000040000000-0x00000000ffffffff]
[    0.000000]   Normal   [mem 0x0000000100000000-0x000000023fffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000040000000-0x000000004005ffff]
[    0.000000]   node   0: [mem 0x0000000040060000-0x000000023fffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000040000000-0x000000023fffffff]
[    0.000000] SBI HSM extension detected
[    0.000000] CPU with hartid=0 is not available
[    0.000000] Falling back to deprecated "riscv,isa"
[    0.000000] riscv: base ISA extensions acdfim
[    0.000000] riscv: ELF capabilities acdfim
[    0.000000] percpu: Embedded 19 pages/cpu s39928 r8192 d29704 u77824
[    0.000000] Kernel command line: root=UUID=2574fd6e-2dbd-4304-a269-a1fe902ce21d rootwait
[    0.000000] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    0.000000] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 2068480
[    0.000000] mem auto-init: stack:off, heap alloc:off, heap free:off
[    0.000000] software IO TLB: area num 4.
[    0.000000] software IO TLB: mapped [mem 0x00000000fa1b1000-0x00000000fe1b1000] (64MB)
[    0.000000] Memory: 8147912K/8388608K available (10395K kernel code, 4956K rwdata, 4096K rodata, 2212K init, 637K bss, 224312K reserved, 16384K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=64 to nr_cpu_ids=4.
[    0.000000] rcu:     RCU debug extended QS entry/exit.
[    0.000000]  Tracing variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 10 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] riscv-intc: 64 local interrupts mapped
[    0.000000] plic: interrupt-controller@c000000: mapped 136 interrupts with 4 handlers for 9 contexts.
[    0.000000] riscv: providing IPIs using SBI IPI extension
[    0.000000] rcu: srcu_init: Setting srcu_struct sizes based on contention.
[    0.000000] clocksource: riscv_clocksource: mask: 0xffffffffffffffff max_cycles: 0x1d854df40, max_idle_ns: 881590404240 ns
[    0.000001] sched_clock: 64 bits at 4MHz, resolution 250ns, wraps every 2199023255500ns
[    0.000204] Calibrating delay loop (skipped), value calculated using timer frequency.. 8.00 BogoMIPS (lpj=40000)
[    0.000218] pid_max: default: 32768 minimum: 301
[    0.000531] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.000700] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    0.001627] CPU node for /cpus/cpu@0 exist but the possible cpu range is :0-3
[    0.002814] RCU Tasks Trace: Setting shift to 2 and lim to 1 rcu_task_cb_adjust=1.
[    0.002920] ASID allocator disabled (0 bits)
[    0.003056] rcu: Hierarchical SRCU implementation.
[    0.003061] rcu:     Max phase no-delay instances is 1000.
[    0.003335] EFI services will not be available.
[    0.003667] smp: Bringing up secondary CPUs ...
[    0.060069] cpu1: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.120104] cpu2: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.180135] cpu3: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.180260] smp: Brought up 1 node, 4 CPUs
[    0.182721] devtmpfs: initialized
[    0.188058] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns
[    0.188076] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.188651] pinctrl core: initialized pinctrl subsystem
[    0.189792] NET: Registered PF_NETLINK/PF_ROUTE protocol family
[    0.190724] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    0.190842] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.191196] thermal_sys: Registered thermal governor 'step_wise'
[    0.191241] cpuidle: using governor menu
[    0.250193] cpu0: Ratio of byte access time to unaligned word access is 0.01, unaligned accesses are slow
[    0.253896] platform soc: Fixed dependency cycle(s) with /soc/interrupt-controller@c000000
[    0.262176] HugeTLB: registered 1.00 GiB page size, pre-allocated 0 pages
[    0.262184] HugeTLB: 0 KiB vmemmap can be freed for a 1.00 GiB page
[    0.262190] HugeTLB: registered 2.00 MiB page size, pre-allocated 0 pages
[    0.262195] HugeTLB: 0 KiB vmemmap can be freed for a 2.00 MiB page
[    0.262771] raid6: skipped pq benchmark and selected int64x8
[    0.262777] raid6: using intx1 recovery algorithm
[    0.263402] SCSI subsystem initialized
[    0.263782] usbcore: registered new interface driver usbfs
[    0.263815] usbcore: registered new interface driver hub
[    0.263848] usbcore: registered new device driver usb
[    0.264070] mc: Linux media interface: v0.10
[    0.264113] videodev: Linux video capture interface: v2.00
[    0.264337] Advanced Linux Sound Architecture Driver Initialized.
[    0.265131] vgaarb: loaded
[    0.265433] clocksource: Switched to clocksource riscv_clocksource
[    0.265765] FS-Cache: Loaded
[    0.267251] NET: Registered PF_INET protocol family
[    0.268472] IP idents hash table entries: 131072 (order: 8, 1048576 bytes, linear)
[    0.280829] tcp_listen_portaddr_hash hash table entries: 4096 (order: 5, 131072 bytes, linear)
[    0.281015] Table-perturb hash table entries: 65536 (order: 6, 262144 bytes, linear)
[    0.281035] TCP established hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.281889] TCP bind hash table entries: 65536 (order: 10, 4194304 bytes, linear)
[    0.288830] TCP: Hash tables configured (established 65536 bind 65536)
[    0.289913] MPTCP token hash table entries: 8192 (order: 6, 393216 bytes, linear)
[    0.290287] UDP hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    0.290812] UDP-Lite hash table entries: 4096 (order: 6, 393216 bytes, linear)
[    0.291474] NET: Registered PF_UNIX/PF_LOCAL protocol family
[    0.292082] RPC: Registered named UNIX socket transport module.
[    0.292090] RPC: Registered udp transport module.
[    0.292094] RPC: Registered tcp transport module.
[    0.292098] RPC: Registered tcp-with-tls transport module.
[    0.292102] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.292119] NET: Registered PF_XDP protocol family
[    0.292134] PCI: CLS 0 bytes, default 64
[    0.292563] Unpacking initramfs...
[    0.302461] Initialise system trusted keyrings
[    0.302713] workingset: timestamp_bits=62 max_order=21 bucket_order=0
[    0.303268] NFS: Registering the id_resolver key type
[    0.303301] Key type id_resolver registered
[    0.303307] Key type id_legacy registered
[    0.303328] nfs4filelayout_init: NFSv4 File Layout Driver Registering...
[    0.303335] nfs4flexfilelayout_init: NFSv4 Flexfile Layout Driver Registering...
[    0.303361] ntfs: driver 2.1.32 [Flags: R/W].
[    0.303383] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.303639] fuse: init (API version 7.39)
[    0.381038] NET: Registered PF_ALG protocol family
[    0.381075] xor: measuring software checksum speed
[    0.385287]    8regs           :  2343 MB/sec
[    0.389541]    8regs_prefetch  :  2337 MB/sec
[    0.393749]    32regs          :  2343 MB/sec
[    0.397994]    32regs_prefetch :  2336 MB/sec
[    0.398002] xor: using function: 32regs (2343 MB/sec)
[    0.398017] Key type asymmetric registered
[    0.398023] Asymmetric key parser 'x509' registered
[    0.398107] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 248)
[    0.398171] io scheduler bfq registered
[    0.413189] CCACHE: DataError @ 0x00000000.080221F8
[    0.413283] CCACHE: DataFail @ 0x00000000.080221DC
[    0.413376] CCACHE: 8 banks, 16 ways, sets/bank=256, bytes/block=64
[    0.413384] CCACHE: Index of the largest way enabled: 15
[    0.414286] Serial: 8250/16550 driver, 6 ports, IRQ sharing disabled
[    0.416803] printk: console [ttyprintk0] enabled
[    0.419190] random: crng init done
[    0.425139] loop: module loaded
[    0.425613] zram: Added device: zram0
[    0.437420] spi-nor spi0.0: gd25lq128d (16384 Kbytes)
[    0.813561] Freeing initrd memory: 5532K
[    0.827970] 4 fixed-partitions partitions found on MTD device 13010000.spi.0
[    0.827986] Creating 4 MTD partitions on "13010000.spi.0":
[    0.828007] 0x000000000000-0x000000080000 : "spl"
[    0.828947] 0x0000000f0000-0x000000100000 : "uboot-env"
[    0.829728] 0x000000100000-0x000000500000 : "uboot"
[    0.830462] 0x000000600000-0x000001000000 : "reserved-data"
[    0.833110] CAN device driver interface
[    0.833900] starfive-dwmac 16030000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[    0.833914] starfive-dwmac 16030000.ethernet:        DWMAC4/5
[    0.833921] starfive-dwmac 16030000.ethernet: DMA HW capability register supported
[    0.833927] starfive-dwmac 16030000.ethernet: RX Checksum Offload Engine supported
[    0.833933] starfive-dwmac 16030000.ethernet: Wake-Up On Lan supported
[    0.833995] starfive-dwmac 16030000.ethernet: TSO supported
[    0.834001] starfive-dwmac 16030000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.834008] starfive-dwmac 16030000.ethernet: Enabled L3L4 Flow TC (entries=1)
[    0.834016] starfive-dwmac 16030000.ethernet: Enabled RFS Flow TC (entries=10)
[    0.834024] starfive-dwmac 16030000.ethernet: TSO feature enabled
[    0.834030] starfive-dwmac 16030000.ethernet: Using 40/40 bits DMA host/device width
[    0.846438] starfive-dwmac 16040000.ethernet: User ID: 0x41, Synopsys ID: 0x52
[    0.846454] starfive-dwmac 16040000.ethernet:        DWMAC4/5
[    0.846461] starfive-dwmac 16040000.ethernet: DMA HW capability register supported
[    0.846467] starfive-dwmac 16040000.ethernet: RX Checksum Offload Engine supported
[    0.846473] starfive-dwmac 16040000.ethernet: Wake-Up On Lan supported
[    0.846527] starfive-dwmac 16040000.ethernet: TSO supported
[    0.846533] starfive-dwmac 16040000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    0.846539] starfive-dwmac 16040000.ethernet: Enabled L3L4 Flow TC (entries=1)
[    0.846548] starfive-dwmac 16040000.ethernet: Enabled RFS Flow TC (entries=10)
[    0.846564] starfive-dwmac 16040000.ethernet: TSO feature enabled
[    0.846571] starfive-dwmac 16040000.ethernet: Using 40/40 bits DMA host/device width
[    0.858861] usbcore: registered new interface driver uas
[    0.858893] usbcore: registered new interface driver usb-storage
[    0.859118] i2c_dev: i2c /dev entries driver
[    0.859351] usbcore: registered new interface driver uvcvideo
[    0.861215] sdhci: Secure Digital Host Controller Interface driver
[    0.861220] sdhci: Copyright(c) Pierre Ossman
[    0.861254] Synopsys Designware Multimedia Card Interface Driver
[    0.861430] sdhci-pltfm: SDHCI platform and OF driver helper
[    0.862014] clocksource: jh7110-timer.ch0: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.862109] clocksource: jh7110-timer.ch1: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.862201] clocksource: jh7110-timer.ch2: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.862296] clocksource: jh7110-timer.ch3: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 79635851949 ns
[    0.862599] usbcore: registered new interface driver usbhid
[    0.862605] usbhid: USB HID core driver
[    0.862632] SPI driver st-accel-spi has no spi_device_id for st,lis302dl-spi
[    0.862638] SPI driver st-accel-spi has no spi_device_id for st,lis3lv02dl-accel
[    0.862644] SPI driver st-accel-spi has no spi_device_id for st,lis3dh-accel
[    0.862649] SPI driver st-accel-spi has no spi_device_id for st,lsm330d-accel
[    0.862654] SPI driver st-accel-spi has no spi_device_id for st,lsm330dl-accel
[    0.862658] SPI driver st-accel-spi has no spi_device_id for st,lsm330dlc-accel
[    0.862664] SPI driver st-accel-spi has no spi_device_id for st,lis331dlh-accel
[    0.862669] SPI driver st-accel-spi has no spi_device_id for st,lsm330-accel
[    0.862674] SPI driver st-accel-spi has no spi_device_id for st,lsm303agr-accel
[    0.862679] SPI driver st-accel-spi has no spi_device_id for st,lis2dh12-accel
[    0.862684] SPI driver st-accel-spi has no spi_device_id for st,lng2dm-accel
[    0.862688] SPI driver st-accel-spi has no spi_device_id for st,h3lis331dl-accel
[    0.862693] SPI driver st-accel-spi has no spi_device_id for st,lis331dl-accel
[    0.862701] SPI driver st-accel-spi has no spi_device_id for st,lsm303c-accel
[    0.862881] riscv-pmu-sbi: SBI PMU extension is available
[    0.862903] riscv-pmu-sbi: 16 firmware and 4 hardware counters
[    0.862909] riscv-pmu-sbi: Perf sampling/filtering is not supported as sscof extension is not available
[    0.863331] usbcore: registered new interface driver snd-usb-audio
[    0.864189] NET: Registered PF_INET6 protocol family
[    0.865218] Segment Routing with IPv6
[    0.865246] In-situ OAM (IOAM) with IPv6
[    0.865327] NET: Registered PF_PACKET protocol family
[    0.865333] can: controller area network core
[    0.865390] NET: Registered PF_CAN protocol family
[    0.865397] can: raw protocol
[    0.865404] can: broadcast manager protocol
[    0.865434] can: netlink gateway - max_hops=1
[    0.865685] Key type dns_resolver registered
[    0.865692] mpls_gso: MPLS GSO support
[    0.880123] Loading compiled-in X.509 certificates
[    0.885728] Btrfs loaded, zoned=no, fsverity=no
[    0.905808] pl08xdmac 16008000.dma-controller: initialized 8 virtual memcpy channels
[    0.905836] pl08xdmac 16008000.dma-controller: initialized 16 virtual slave channels
[    0.907219] debugfs: Directory '16008000.dma-controller' with parent 'dmaengine' already present!
[    0.907237] pl08xdmac 16008000.dma-controller: DMA: PL080 rev0 at 0x16008000 irq 30
[    0.907873] gpio gpiochip0: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    0.908195] starfive-jh7110-sys-pinctrl 13040000.pinctrl: StarFive GPIO chip registered 64 GPIOs
[    0.909034] gpio gpiochip1: Static allocation of GPIO base is deprecated, use dynamic allocation.
[    0.909258] starfive-jh7110-aon-pinctrl 17020000.pinctrl: StarFive GPIO chip registered 4 GPIOs
[    0.909886] pcie-starfive 940000000.pcie: host bridge /soc/pcie@940000000 ranges:
[    0.909927] pcie-starfive 940000000.pcie:      MEM 0x0030000000..0x0037ffffff -> 0x0030000000
[    0.909946] pcie-starfive 940000000.pcie:      MEM 0x0900000000..0x093fffffff -> 0x0900000000
[    1.145443] pcie-starfive 940000000.pcie: port link up
[    1.146572] pcie-starfive 940000000.pcie: PCI host bridge to bus 0000:00
[    1.146582] pci_bus 0000:00: root bus resource [bus 00-ff]
[    1.146592] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[    1.146601] pci_bus 0000:00: root bus resource [mem 0x900000000-0x93fffffff pref]
[    1.146633] pci 0000:00:00.0: [1556:1111] type 01 class 0x060400
[    1.146697] pci 0000:00:00.0: supports D1 D2
[    1.146704] pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    1.148458] pci 0000:01:00.0: [1106:3483] type 00 class 0x0c0330
[    1.148485] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]
[    1.148572] pci 0000:01:00.0: PME# supported from D0 D3cold
[    1.148751] pci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01
[    1.148775] pci 0000:00:00.0: BAR 8: assigned [mem 0x30000000-0x300fffff]
[    1.148787] pci 0000:01:00.0: BAR 0: assigned [mem 0x30000000-0x30000fff 64bit]
[    1.148805] pci 0000:00:00.0: PCI bridge to [bus 01]
[    1.148814] pci 0000:00:00.0:   bridge window [mem 0x30000000-0x300fffff]
[    1.149094] pcieport 0000:00:00.0: PME: Signaling with IRQ 48
[    1.149224] pci 0000:01:00.0: enabling device (0000 -> 0002)
[    1.149415] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.149436] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 1
[    1.149802] xhci_hcd 0000:01:00.0: hcc params 0x002841eb hci version 0x100 quirks 0x0000000000000890
[    1.150224] xhci_hcd 0000:01:00.0: xHCI Host Controller
[    1.150239] xhci_hcd 0000:01:00.0: new USB bus registered, assigned bus number 2
[    1.150252] xhci_hcd 0000:01:00.0: Host supports USB 3.0 SuperSpeed
[    1.150895] hub 1-0:1.0: USB hub found
[    1.150939] hub 1-0:1.0: 1 port detected
[    1.151874] hub 2-0:1.0: USB hub found
[    1.151911] hub 2-0:1.0: 4 ports detected
[    1.152840] pcie-starfive 9c0000000.pcie: host bridge /soc/pcie@9c0000000 ranges:
[    1.152877] pcie-starfive 9c0000000.pcie:      MEM 0x0038000000..0x003fffffff -> 0x0038000000
[    1.152896] pcie-starfive 9c0000000.pcie:      MEM 0x0980000000..0x09bfffffff -> 0x0980000000
[    1.435441] usb 1-1: new high-speed USB device number 2 using xhci_hcd
[    1.619072] hub 1-1:1.0: USB hub found
[    1.619315] hub 1-1:1.0: 4 ports detected
[    1.965443] usb 1-1.1: new low-speed USB device number 3 using xhci_hcd
[    2.112588] input: USB-compliant keyboard as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.0/0003:062A:0201.0001/input/input0
[    2.175771] hid-generic 0003:062A:0201.0001: input: USB HID v1.10 Keyboard [USB-compliant keyboard] on usb-0000:01:00.0-1.1/input0
[    2.184207] USB-compliant keyboard: Invalid code 773 type 1
[    2.184331] input: USB-compliant keyboard Mouse as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:062A:0201.0002/input/input1
[    2.184597] input: USB-compliant keyboard Consumer Control as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:062A:0201.0002/input/input2
[    2.184807] input: USB-compliant keyboard System Control as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:062A:0201.0002/input/input3
[    2.185021] input: USB-compliant keyboard as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.1/1-1.1:1.1/0003:062A:0201.0002/input/input4
[    2.185138] hid-generic 0003:062A:0201.0002: input: USB HID v1.10 Mouse [USB-compliant keyboard] on usb-0000:01:00.0-1.1/input1
[    2.285455] usb 1-1.2: new low-speed USB device number 4 using xhci_hcd
[    2.385445] pcie-starfive 9c0000000.pcie: port link down
[    2.386317] pcie-starfive 9c0000000.pcie: PCI host bridge to bus 0001:00
[    2.386328] pci_bus 0001:00: root bus resource [bus 00-ff]
[    2.386337] pci_bus 0001:00: root bus resource [mem 0x38000000-0x3fffffff]
[    2.386346] pci_bus 0001:00: root bus resource [mem 0x980000000-0x9bfffffff pref]
[    2.386376] pci 0001:00:00.0: [1556:1111] type 01 class 0x060400
[    2.386438] pci 0001:00:00.0: supports D1 D2
[    2.386445] pci 0001:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
[    2.388276] pci_bus 0001:01: busn_res: [bus 01-ff] end is updated to 01
[    2.388294] pci 0001:00:00.0: PCI bridge to [bus 01]
[    2.388566] pcieport 0001:00:00.0: PME: Signaling with IRQ 65
[    2.393239] dw_axi_dmac_platform 16050000.dma-controller: DesignWare AXI DMA Controller, 4 channels
[    2.393759] printk: console [ttyS0] disabled
[    2.394097] 10000000.serial: ttyS0 at MMIO 0x10000000 (irq = 66, base_baud = 1500000) is a 16550A
[    2.394134] printk: console [ttyS0] enabled
[    4.208451] ssp-pl022 10060000.spi: ARM PL022 driver, device ID: 0x00041022
[    4.215474] ssp-pl022 10060000.spi: mapped registers from 0x0000000010060000 to 00000000afba228f
[    4.216006] dwmmc_starfive 16020000.mmc: IDMAC supports 32-bit address mode.
[    4.226711] axp20x-i2c 5-0036: AXP20x variant AXP15060 found
[    4.231346] dwmmc_starfive 16020000.mmc: Using internal DMA controller.
[    4.240229] axp20x-i2c 5-0036: AXP20X driver loaded
[    4.243567] dwmmc_starfive 16020000.mmc: Version ID is 290a
[    4.249914] dwmmc_starfive 16010000.mmc: IDMAC supports 32-bit address mode.
[    4.254050] dwmmc_starfive 16020000.mmc: DW MMC controller at irq 71,32 bit host data width,32 deep fifo
[    4.256528] cpufreq: cpufreq_online: CPU0: Running at unlisted initial frequency: 999999 KHz, changing to: 1500000 KHz
[    4.261110] dwmmc_starfive 16010000.mmc: Using internal DMA controller.
[    4.270724] mmc_host mmc1: card is polling.
[    4.281268] dwmmc_starfive 16010000.mmc: Version ID is 290a
[    4.281309] dwmmc_starfive 16010000.mmc: DW MMC controller at irq 92,32 bit host data width,32 deep fifo
[    4.307432] mmc_host mmc0: card is non-removable.
[    4.324674] input: Logitech USB-PS/2 Optical Mouse as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.2/1-1.2:1.0/0003:046D:C03D.0003/input/input5
[    4.341454] hid-generic 0003:046D:C03D.0003: input: USB HID v1.10 Mouse [Logitech USB-PS/2 Optical Mouse] on usb-0000:01:00.0-1.2/input0
[    4.445503] usb 1-1.3: new full-speed USB device number 5 using xhci_hcd
[    4.505563] mmc_host mmc1: Bus speed (slot 0) = 204799999Hz (slot req 400000Hz, actual 399999HZ div = 256)
[    4.525484] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 400000Hz, actual 399999HZ div = 256)
[    4.595535] input: UGTABLET 15.6 inch PenDisplay Mouse as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:28BD:090D.0004/input/input6
[    4.613270] input: UGTABLET 15.6 inch PenDisplay Keyboard as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.0/0003:28BD:090D.0004/input/input7
[    4.630818] hid-generic 0003:28BD:090D.0004: input: USB HID v1.00 Mouse [UGTABLET 15.6 inch PenDisplay] on usb-0000:01:00.0-1.3/input0
[    4.648070] input: UGTABLET 15.6 inch PenDisplay Stylus as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:28BD:090D.0005/input/input8
[    4.665256] input: UGTABLET 15.6 inch PenDisplay as /devices/platform/soc/940000000.pcie/pci0000:00/0000:00:00.0/0000:01:00.0/usb1/1-1/1-1.3/1-1.3:1.1/0003:28BD:090D.0005/input/input9
[    4.681707] hid-generic 0003:28BD:090D.0005: input: USB HID v1.00 Device [UGTABLET 15.6 inch PenDisplay] on usb-0000:01:00.0-1.3/input1
[    4.696160] hid-generic 0003:28BD:090D.0006: device has no listeners, quitting
[    4.745898] clk: Disabling unused clocks
[    4.750559] ALSA device list:
[    4.753586]   No soundcards found.
[    4.761687] Freeing unused kernel image (initmem) memory: 2212K
[    4.776506] Checked W+X mappings: passed, no W+X pages found
[    4.782194] rodata_test: all tests were successful
[    4.787069] Run /init as init process
Loading, please wait...
Starting systemd-udevd version 255-1
[    4.955494] mmc_host mmc1: Bus speed (slot 0) = 204799999Hz (slot req 300000Hz, actual 299415HZ div = 342)
[    4.985826] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 300000Hz, actual 299415HZ div = 342)
[    5.284847] starfive-dwmac 16030000.ethernet end0: renamed from eth0
[    5.318700] starfive-dwmac 16040000.ethernet end1: renamed from eth1
Begin: Loading essential drivers ... done.
Begin: Running /scripts/init-premount ... done.
Begin: Mounting root file system ... Begin: Running /scripts/local-top ... done.
Begin: Running /scripts/local-premount ... done.
[    5.445530] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 200000Hz, actual 199999HZ div = 512)
[    5.463932] mmc_host mmc1: Bus speed (slot 0) = 204799999Hz (slot req 50000000Hz, actual 34133333HZ div = 3)
[    5.473947] mmc1: new high speed SDHC card at address 0001
[    5.481283] mmcblk1: mmc1:0001 0008G 7.54 GiB
[    5.492135]  mmcblk1: p1 p2 p3
[    5.885499] mmc_host mmc0: Bus speed (slot 0) = 204799999Hz (slot req 100000Hz, actual 99999HZ div = 1024)
Begin: Will now check root file system ... fsck from util-linux 2.39.3
[/sbin/fsck.ext4 (1) -- /dev/mmcblk1p3] fsck.ext4 -a -C0 /dev/mmcblk1p3 
rootfs: recovering journal
rootfs: clean, 12049/497760 files, 112690/1973243 blocks
done.
[    6.111724] mmc0: Failed to initialize a non-removable card
[    7.152690] EXT4-fs (mmcblk1p3): mounted filesystem 2574fd6e-2dbd-4304-a269-a1fe902ce21d ro with ordered data mode. Quota mode: disabled.
done.
Begin: Running /scripts/local-bottom ... done.
Begin: Running /scripts/init-bottom ... done.
[    8.208431] systemd[1]: System time before build time, advancing clock.
[    8.342708] systemd[1]: systemd 255-1 running in system mode (+PAM +AUDIT +SELINUX +APPARMOR +IMA +SMACK +SECCOMP +GCRYPT -GNUTLS +OPENSSL +ACL +BLKID +CURL +ELFUTILS +FIDO2 +IDN2 -IDN +IPTC +KMOD +LIBCRYPTSETUP +LIBFDISK +PCRE2 -PWQUALITY +P11KIT +QRENCODE +TPM2 +BZIP2 +LZ4 +XZ +ZLIB +ZSTD -BPF_FRAMEWORK -XKBCOMMON +UTMP +SYSVINIT default-hierarchy=unified)
[    8.374588] systemd[1]: Detected architecture riscv64.

Welcome to Debian GNU/Linux trixie/sid!

[    8.417542] systemd[1]: Hostname set to <visionfive2>.
[    9.301461] systemd[1]: Queued start job for default target graphical.target.
[    9.403860] systemd[1]: Created slice system-getty.slice - Slice /system/getty.
[  OK  ] Created slice system-getty.slice - Slice /system/getty.
[    9.446696] systemd[1]: Created slice system-modprobe.slice - Slice /system/modprobe.
[  OK  ] Created slice system-modprobe.slice - Slice /system/modprobe.
[    9.488911] systemd[1]: Created slice system-serial\x2dgetty.slice - Slice /system/serial-getty.
[  OK  ] Created slice system-serial\x2dget…slice - Slice /system/serial-getty.
[    9.537698] systemd[1]: Created slice user.slice - User and Session Slice.
[  OK  ] Created slice user.slice - User and Session Slice.
[    9.576400] systemd[1]: Started systemd-ask-password-console.path - Dispatch Password Requests to Console Directory Watch.
[  OK  ] Started systemd-ask-password-conso…equests to Console Directory Watch.
[    9.626300] systemd[1]: Started systemd-ask-password-wall.path - Forward Password Requests to Wall Directory Watch.
[  OK  ] Started systemd-ask-password-wall.…d Requests to Wall Directory Watch.
[    9.676455] systemd[1]: proc-sys-fs-binfmt_misc.automount - Arbitrary Executable File Formats File System Automount Point was skipped because of an unmet condition check (ConditionPathExists=/proc/sys/fs/binfmt_misc).
[    9.696431] systemd[1]: Reached target cryptsetup.target - Local Encrypted Volumes.
[  OK  ] Reached target cryptsetup.target - Local Encrypted Volumes.
[    9.735897] systemd[1]: Reached target integritysetup.target - Local Integrity Protected Volumes.
[  OK  ] Reached target integritysetup.targ… Local Integrity Protected Volumes.
[    9.776037] systemd[1]: Reached target paths.target - Path Units.
[  OK  ] Reached target paths.target - Path Units.
[    9.815744] systemd[1]: Reached target remote-fs.target - Remote File Systems.
[  OK  ] Reached target remote-fs.target - Remote File Systems.
[    9.855913] systemd[1]: Reached target slices.target - Slice Units.
[  OK  ] Reached target slices.target - Slice Units.
[    9.895882] systemd[1]: Reached target swap.target - Swaps.
[  OK  ] Reached target swap.target - Swaps.
[    9.936136] systemd[1]: Reached target veritysetup.target - Local Verity Protected Volumes.
[  OK  ] Reached target veritysetup.target - Local Verity Protected Volumes.
[    9.976526] systemd[1]: Listening on systemd-fsckd.socket - fsck to fsckd communication Socket.
[  OK  ] Listening on systemd-fsckd.socket …fsck to fsckd communication Socket.
[   10.016399] systemd[1]: Listening on systemd-initctl.socket - initctl Compatibility Named Pipe.
[  OK  ] Listening on systemd-initctl.socke…- initctl Compatibility Named Pipe.
[   10.056509] systemd[1]: Listening on systemd-journald-dev-log.socket - Journal Socket (/dev/log).
[  OK  ] Listening on systemd-journald-dev-…socket - Journal Socket (/dev/log).
[   10.097092] systemd[1]: Listening on systemd-journald.socket - Journal Socket.
[  OK  ] Listening on systemd-journald.socket - Journal Socket.
[   10.135825] systemd[1]: systemd-pcrextend.socket - TPM2 PCR Extension (Varlink) was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.152731] systemd[1]: Listening on systemd-udevd-control.socket - udev Control Socket.
[  OK  ] Listening on systemd-udevd-control.socket - udev Control Socket.
[   10.196911] systemd[1]: Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[  OK  ] Listening on systemd-udevd-kernel.socket - udev Kernel Socket.
[   10.315977] systemd[1]: Mounting dev-hugepages.mount - Huge Pages File System...
         Mounting dev-hugepages.mount - Huge Pages File System...
[   10.360842] systemd[1]: Mounting dev-mqueue.mount - POSIX Message Queue File System...
         Mounting dev-mqueue.mount - POSIX Message Queue File System...
[   10.408558] systemd[1]: Mounting sys-kernel-debug.mount - Kernel Debug File System...
         Mounting sys-kernel-debug.mount - Kernel Debug File System...
[   10.446083] systemd[1]: sys-kernel-tracing.mount - Kernel Trace File System was skipped because of an unmet condition check (ConditionPathExists=/sys/kernel/tracing).
[   10.468336] systemd[1]: Starting kmod-static-nodes.service - Create List of Static Device Nodes...
         Starting kmod-static-nodes.service…eate List of Static Device Nodes...
[   10.509214] systemd[1]: Starting modprobe@configfs.service - Load Kernel Module configfs...
         Starting modprobe@configfs.service - Load Kernel Module configfs...
[   10.552004] systemd[1]: Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
         Starting modprobe@dm_mod.service - Load Kernel Module dm_mod...
[   10.599260] systemd[1]: Starting modprobe@drm.service - Load Kernel Module drm...
         Starting modprobe@drm.service - Load Kernel Module drm...
[   10.639269] systemd[1]: Starting modprobe@efi_pstore.service - Load Kernel Module efi_pstore...
         Starting modprobe@efi_pstore.servi… - Load Kernel Module efi_pstore...
[   10.679216] systemd[1]: Starting modprobe@fuse.service - Load Kernel Module fuse...
[   10.682273] device-mapper: ioctl: 4.48.0-ioctl (2023-03-01) initialised: dm-devel@redhat.com
         Starting modprobe@fuse.service - Load Kernel Module fuse...
[   10.732121] systemd[1]: Starting modprobe@loop.service - Load Kernel Module loop...
         Starting modprobe@loop.service - Load Kernel Module loop...
[   10.775991] systemd[1]: systemd-fsck-root.service - File System Check on Root Device was skipped because of an unmet condition check (ConditionPathExists=!/run/initramfs/fsck-root).
[   10.799287] systemd[1]: Starting systemd-journald.service - Journal Service...
         Starting systemd-journald.service - Journal Service...
[   10.840258] systemd[1]: Starting systemd-modules-load.service - Load Kernel Modules...
         Starting systemd-modules-load.service - Load Kernel Modules...
[   10.875762] systemd[1]: systemd-pcrmachine.service - TPM2 PCR Machine ID Measurement was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.894332] systemd[1]: Starting systemd-remount-fs.service - Remount Root and Kernel File Systems...
         Starting systemd-remount-fs.servic…unt Root and Kernel File Systems...
[   10.918114] systemd-journald[201]: Collecting audit messages is disabled.
[   10.935958] systemd[1]: systemd-tpm2-setup-early.service - TPM2 SRK Setup (Early) was skipped because of an unmet condition check (ConditionSecurity=measured-uki).
[   10.954992] systemd[1]: Starting systemd-udev-trigger.service - Coldplug All udev Devices...
         Starting systemd-udev-trigger.service - Coldplug All udev Devices...
[   11.001839] systemd[1]: Mounted dev-hugepages.mount - Huge Pages File System.
[  OK  ] Mounted dev-hugepages.mount - Huge Pages File System.
[   11.040955] EXT4-fs (mmcblk1p3): re-mounted 2574fd6e-2dbd-4304-a269-a1fe902ce21d r/w. Quota mode: disabled.
[   11.051378] systemd[1]: Started systemd-journald.service - Journal Service.
[  OK  ] Started systemd-journald.service - Journal Service.
[  OK  ] Mounted dev-mqueue.mount - POSIX Message Queue File System.
[  OK  ] Mounted sys-kernel-debug.mount - Kernel Debug File System.
[  OK  ] Finished kmod-static-nodes.service…Create List of Static Device Nodes.
[  OK  ] Finished modprobe@configfs.service - Load Kernel Module configfs.
[  OK  ] Finished modprobe@dm_mod.service - Load Kernel Module dm_mod.
[  OK  ] Finished modprobe@drm.service - Load Kernel Module drm.
[  OK  ] Finished modprobe@efi_pstore.service - Load Kernel Module efi_pstore.
[  OK  ] Finished modprobe@fuse.service - Load Kernel Module fuse.
[  OK  ] Finished modprobe@loop.service - Load Kernel Module loop.
[  OK  ] Finished systemd-modules-load.service - Load Kernel Modules.
[  OK  ] Finished systemd-remount-fs.servic…mount Root and Kernel File Systems.
[  OK  ] Finished systemd-udev-trigger.service - Coldplug All udev Devices.
         Mounting sys-fs-fuse-connections.mount - FUSE Control File System...
         Mounting sys-kernel-config.mount - Kernel Configuration File System...
         Starting ifupdown-pre.service - He…synchronize boot up for ifupdown...
         Starting systemd-journal-flush.ser…sh Journal to Persistent Storage...
         Starting systemd-random-seed.service - Load/Save OS Random Seed...
[   11.820788] systemd-journald[201]: Received client request to flush runtime journal.
         Starting systemd-sysctl.service - Apply Kernel Variables...
[   11.849829] systemd-journald[201]: File /var/log/journal/331110f5561149d796e01023cfb9bcad/system.journal corrupted or uncleanly shut down, renaming and replacing.
         Starting systemd-tmpfiles-setup-de… Device Nodes in /dev gracefully...
[  OK  ] Mounted sys-fs-fuse-connections.mount - FUSE Control File System.
[  OK  ] Mounted sys-kernel-config.mount - Kernel Configuration File System.
[  OK  ] Finished ifupdown-pre.service - He…o synchronize boot up for ifupdown.
[  OK  ] Finished systemd-random-seed.service - Load/Save OS Random Seed.
[  OK  ] Finished systemd-sysctl.service - Apply Kernel Variables.
[  OK  ] Finished systemd-journal-flush.ser…lush Journal to Persistent Storage.
[  OK  ] Finished systemd-tmpfiles-setup-de…ic Device Nodes in /dev gracefully.
         Starting systemd-tmpfiles-setup-de…eate Static Device Nodes in /dev...
[  OK  ] Finished systemd-tmpfiles-setup-de…Create Static Device Nodes in /dev.
[  OK  ] Reached target local-fs-pre.target…Preparation for Local File Systems.
[  OK  ] Reached target local-fs.target - Local File Systems.
[  OK  ] Listening on systemd-sysext.socket…tension Image Management (Varlink).
         Starting networking.service - Raise network interfaces...
         Starting systemd-tmpfiles-setup.se…e Volatile Files and Directories...
         Starting systemd-udevd.service - R…ager for Device Events and Files...
[  OK  ] Finished systemd-tmpfiles-setup.se…ate Volatile Files and Directories.
[  OK  ] Started systemd-udevd.service - Ru…anager for Device Events and Files.
[  OK  ] Finished networking.service - Raise network interfaces.
[  OK  ] Found device dev-ttyS0.device - /dev/ttyS0.
[  OK  ] Reached target usb-gadget.target - Hardware activated USB gadget.
         Starting systemd-timesyncd.service - Network Time Synchronization...
         Starting systemd-update-utmp.servi…ord System Boot/Shutdown in UTMP...
[  OK  ] Finished systemd-update-utmp.servi…ecord System Boot/Shutdown in UTMP.
[  OK  ] Started systemd-timesyncd.service - Network Time Synchronization.
[  OK  ] Reached target sysinit.target - System Initialization.
[  OK  ] Started systemd-tmpfiles-clean.tim…y Cleanup of Temporary Directories.
[  OK  ] Reached target time-set.target - System Time Set.
[  OK  ] Started apt-daily.timer - Daily apt download activities.
[  OK  ] Started apt-daily-upgrade.timer - …y apt upgrade and clean activities.
[  OK  ] Started dpkg-db-backup.timer - Daily dpkg database backup timer.
[  OK  ] Started e2scrub_all.timer - Period…Metadata Check for All Filesystems.
[  OK  ] Started fstrim.timer - Discard unused filesystem blocks once a week.
[  OK  ] Started logrotate.timer - Daily rotation of log files.
[  OK  ] Reached target timers.target - Timer Units.
[  OK  ] Listening on dbus.socket - D-Bus System Message Bus Socket.
[  OK  ] Reached target sockets.target - Socket Units.
[  OK  ] Reached target basic.target - Basic System.
[  OK  ] Started cron.service - Regular background program processing daemon.
         Starting dbus.service - D-Bus System Message Bus...
         Starting dhcpcd.service - DHCP Client Daemon on all interfaces...
         Starting e2scrub_reap.service - Re…ne ext4 Metadata Check Snapshots...
         Starting systemd-logind.service - User Login Management...
[  OK  ] Started dbus.service - D-Bus System Message Bus.
[  OK  ] Finished e2scrub_reap.service - Re…line ext4 Metadata Check Snapshots.
[   14.863483] 8021q: 802.1Q VLAN Support v1.8
[  OK  ] Started systemd-logind.service - User Login Management.
[  OK  ] Listening on systemd-rfkill.socket…ll Switch Status /dev/rfkill Watch.
[   15.283913] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[   15.312587] Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[   15.319863] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[   15.328532] cfg80211: failed to load regulatory.db
[  OK  ] Started dhcpcd.service - DHCP Client Daemon on all interfaces.
[  OK  ] Reached target network.target - Network.
[   15.448375] starfive-dwmac 16030000.ethernet end0: Register MEM_TYPE_PAGE_POOL RxQ-0
         Starting ssh.s[   15.459767] starfive-dwmac 16030000.ethernet end0: PHY [stmmac-0:00] driver [YT8531 Gigabit Ethernet] (irq=POLL)
ervice - Ope[   15.470883] dwmac4: Master AXI performs fixed burst length
nBSD Secure Shel[   15.477704] starfive-dwmac 16030000.ethernet end0: No Safety Features support found
l server...
[   15.486750] starfive-dwmac 16030000.ethernet end0: IEEE 1588-2008 Advanced Timestamp supported
[   15.499504] starfive-dwmac 16030000.ethernet end0: configuring for phy/rgmii-id link mode
         Startin[   15.509127] 8021q: adding VLAN 0 to HW filter on device end0
g syste[   15.514968] starfive-dwmac 16030000.ethernet end0: Adding VLAN ID 0 is not supported
md-user-sessions[   15.525115] starfive-dwmac 16040000.ethernet end1: Register MEM_TYPE_PAGE_POOL RxQ-0
.service - Permit User Sessi[   15.535185] starfive-dwmac 16040000.ethernet end1: PHY [stmmac-1:00] driver [Generic PHY] (irq=POLL)
ons...
[   15.545170] dwmac4: Master AXI performs fixed burst length
[   15.551293] starfive-dwmac 16040000.ethernet end1: No Safety Features support found
[   15.559006] starfive-dwmac 16040000.ethernet end1: IEEE 1588-2008 Advanced Timestamp supported
[   15.568154] starfive-dwmac 16040000.ethernet end1: configuring for phy/rgmii-id link mode
[   15.579732] 8021q: adding VLAN 0 to HW filter on device end1
[   15.585459] starfive-dwmac 16040000.ethernet end1: Adding VLAN ID 0 is not supported
[  OK  ] Finished systemd-user-sessions.service - Permit User Sessions.
[  OK  ] Started serial-getty@ttyS0.service - Serial Getty on ttyS0.
[  OK  ] Reached target getty.target - Login Prompts.
[  OK  ] Started ssh.service - OpenBSD Secure Shell server.
[  OK  ] Reached target multi-user.target - Multi-User System.
[  OK  ] Reached target graphical.target - Graphical Interface.
         Starting systemd-update-utmp-runle…- Record Runlevel Change in UTMP...
[  OK  ] Finished systemd-update-utmp-runle…e - Record Runlevel Change in UTMP.

Debian GNU/Linux trixie/sid visionfive2 ttyS0

visionfive2 login: [   18.638292] starfive-dwmac 16030000.ethernet end0: Link is Up - 1Gbps/Full - flow control rx/tx

[inindev]

It looks like you were able to boot the image.